Friday, October 7, 2011

New Kit: Velleman Mk102 Flashing LEDs


New Kit: Velleman Mk102

This is my first electronics kit from Velleman: a pair of flashing red LEDs. Wired to each LED is its own potentiometer that I can use to control the flash time of the lights. The slot at the top of the potentiometer is tiny so I have to use a precision flat head screwdriver to operate it (clockwise shortens the flash time, counter-clockwise lengthens it).

The unit itself is about 1.25" square and fits 13 components. These parts consist of four resistors, two transistors, two poteniometers, two red LEDs, two electrolytic capacitors and a 9-volt battery clip.

This was my first go at soldering but I am very pleased with the results. First of all, nothing melted, blew up in my face or otherwise malfunctioned. Also, there were no shorted connections or reversed polarities. For future kits, I will work harder on covering the copper pads completely and avoiding those big unnecessary blobs of solder I found on some of the joints.



I read on the Velleman product page that this kit is good for model construction. Most likely they are used in model railroad settings, for example some kind of blinking crossing guard lights. There must be some way to use wires to light the LED bulb while they're not fastened to the circuit board, allowing more flexibility for light positioning.

Finally, I'm trying to think of a way to modify this circuit. The first thing to come to mind is changing the color of the LEDs bulbs will probably require a change in resistor values as well.

Here's some video of the Mk102 in action!


Wednesday, October 5, 2011

LEDs in Series and Parallel

LEDs in Series and in Parallel



My last post covered an extremely simple circuit consisting of a voltage supply, an LED light and a resistor. However, I anticipate there will come a time when I will need to wire multiple lights for a project.

LED in Series

This one was pretty straightforward: I simply summed up the forward voltage of both of my LEDs and plugged the total into the resistor value formula. The series setup the most efficient way to light multiple LED because they are all running off of the same current.




LED in Parallel

I’ll freely admit that I had a hard time with this one. I got the wiring wrong quite a few times and burned out a lot of bulbs (took a while to get that burnt plastic smell out of my room). Here’s one of the unsuccessful attempts:


This circuit starts of very bright...

...and then quickly burns out.



This one was a winner:




For the next post, I will put together a Velleman MK102 flashing LED light kit.

Friday, August 5, 2011

My First Circuit




I read some where that lighting up some LEDs with a battery is like the electronic version of "Hello World," so I thought it would be a good place to start.


When I built my computer way back when, the power light would not illuminate even though the machine itself was running. To be honest, I can’t even remember what I did to fix it, but when I turned the machine back on and that little LED indicator lit up, I felt a triumphant jolt that, was almost as intense as the one I felt at the thought that I build my first computer. Here was something that wasn’t working and I fixed it, without a manual or a software wizard or help from one of my techie friends. That memory still gives me a warm, fuzzy feeling so it’s nice to start this present endeavor working with LEDs again.

----------------------


I’m using a 9 volt battery to power to power my first circuit. Since a single, red standard LED has a typical forward voltage (VF) of 1.7V, a 9V will easily blow out the bulb. To ensure that this doesn’t happen, I will use a resistor in my circuit. The formula for calculating resistor values is:
R = (VS - VL) / I
VS = supply voltage (the battery)
VL = load voltage (in this case, the LED is the load. Note that this is the same value as the LED’s VF)
I = LED current in amperes
R = value of the resistor, in ohms, that will allow enough current to pass to the LED without blowing it out1.
The LED current for my circuit is 30 milliamperes (mA), which converts to 0.03 amperes. In the case of my single, red LED, my calculation goes like this:
R = (VS - VL) / I
R = (9 - 1.7)/0.03
R = 7.3/0.03
R = 243.33 Ohms
Since I don’t have any resistors that are exactly this value, I would normally round up to the next higher value (270 Ohm). Unfortunately, my still-growing supply of electronic components lack even these (another trip to Radio Shack, anyone?), so I’ll use one of my 330 Ohms. (Note: if you want to skip manual calculations there are some pretty neat resistor value calculators out there2.)
Voila!


Remember to always have a resistor in place before powering an LED. I tried one circuit with just the battery and the LED and the bulb lit up for about a quarter of a second, went dim and started smoking.

Next time I’ll talk about wiring LEDs in series and in parallel.

Part List:

Breadboad
9V battery
9V battery snap connectors
1 resistor (270 Ohm for a single red or yellow LED; 330 Ohm for a single green one)
1 LED (red, yellow or green)

References:

1.) The Electronics Club: Light Emitting Diodes (LEDs)
2.) LEDZ.com: LED Resistor Calculator

Welcome to Electro-n00b


Hello, and welcome to Electro-n00b. My name is Liz and as the title states I am pretty much a complete novice to basic electronic hobby projects. This is not to say that I’m in the dark on all things technical: I enjoy tinkering around with both the hardware and software on my computer, but now I want to try something new.

I am still in somewhat of an exploratory phase and this blog will reflect that. Some of the things I will explore and talk about include:

-Circuits and projects I am working on
-Basic electrical concepts
-DIY electronic applications
-Hackerspace/DIY news and culture
-Impressions of electronic equipment/books/kits

This blog is primarily for those new to electronics such as myself who want to learn from the experiences of others. In the beginning, this blog won't be very heavy on the advanced technical stuff, though as my skills grow that will change. For now, I am more likely to point you to the most accurate resources rather than try to teach something I just learned five minutes ago.

I invite everyone to either comment on any posts they find interesting, or else drop me a line. Fellow n00bs, feel free to ask questions about anything you see or suggest topics you are interested in hearing more about.

Let’s have fun together!
Liz